 |
|||
|
|
|||
|
|
|||
| ||||||||||
|
|
 TM 55-1520-238-S
221.21 Load Four Main Rotor Blades. Position
221.14 Load One Horizontal Stabilator. Position
two main rotor blade rack sets holding two blades each
one stabilator on cargo floor under tail rotor blade of heli-
copter number five (fig. FO1).
fuselage (fig. FO1).
221.15 Load Helicopter Number Four Tail
221.22 Load Helicopter Number Two Tail
First. Load helicopter number four tail first using same
First. Load helicopter number two tail first using same
loading procedures used when loading helicopter num-
loading procedures used when loading helicopter num-
ber five (para 221.12) with following exceptions:
ber five (para 221.12) with following exceptions:
a. Position Helicopter. Position helicopter
CAUTION
to left side of cargo compartment. Ensure
that left main landing gear tire is positioned
on BL 16L.
When winching helicopter number
b. Maneuver Tail Rotor. Maneuver tail rotor
four into position, extreme care must
around tail rotor of helicopter number three
betaken to prevent tail rotor contacting
and ensure clearance between engine na-
tail rotor of helicopter number six.
celle and tail rotor of helicopter number
three.
a. Stop Winching. Stop winching helicop-
ter when main gear tires reach FS 1500.
c. Stop Winching. Stop winching helicop-
ter when main landing gear tire reaches FS
b. Position Helicopter. Manually move he-
1965.
licopter forward in cargo aircraft while ma-
d. Position Helicopter. Manually move he-
neuvering tail rotor to left and past tail rotor
licopter toward forward end of cargo
of helicopter number six. Move helicopter
compartment so that troop stair ladder will
as far as possible forward in cargo aircraft.
clear nose of helicopter (fig. FO1).
Ensure that main landing gear tires are for-
221.23 Load Four Main Rotor Blades. Position
ward of FS1265 (fig. FO1).
two main rotor blade rack sets holding two blades each
221.16 Load Four Main Rotor Blades. Position
two main rotor blade rack sets holding two blades each
selage (fig. FO1).
221.24 Load Six Tail Rotor Blades. Position three
fuselage (fig. FO1).
tail rotor blade supports holding two blades (fig. 27) on
221.17 Load
Two
Horizontal
Stabilators.
left side of cargo floor, outboard of helicopter number
Position two stabilators on cargo floor under nose of he-
two tailboom (fig. FO1).
licopter number five (fig. FO1).
221.18 Load Helicopter Number Three Nose
CAUTION
First. Load helicopter number three nose first using
same loading procedures used when loading helicopter
Ensure that troop stair ladder is ex-
number six (para 221.7) with following exceptions:
tended prior to loading helicopter
number one.
CAUTION
221.25 Load Helicopter Number One Tail
First. Load helicopter number one tail first using same
loading procedures used when loading helicopter num-
Ensure winch cable does not contact
ber five (para 221.12) with following exceptions:
components that have been placed un-
a. Position Helicopter. Position helicopter
der helicopters.
to right of cargo compartment, with its tail
a. Winching Helicopter. Winch helicopter
between number three helicopter and right
into cargo compartment with helicopter left
side of cargo compartment.
main landing gear tire on BL 0.
b. Stop Winching. Stop winching helicop-
ter when main landing gear tire are forward
b. Stop Winching. Stop winching helicop-
of cargo ramp crest.
ter when main gear tires is at FS 1380.
Manually move helicopter as far forward as
c. Position Helicopter. Manually move he-
possible.
licopter as far forward of FS 1965 as pos-
sible (fig. FO1).
221.19 Load Hydraulic Cart. Place hydraulic cart
to right of helicopter number three (fig. FO1).
two main rotor blade rack sets holding two blades each
221.20 Temporarily Install 30MM Gun and Tur-
ret. Temporarily install 30MM gun and turret on heli-
fuselage (fig. FO1).
copter number three (para 221.8).
240
Change 1
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals