 |
|||
|
|
|||
|
|
|||
| ||||||||||
|
|
 TM 9-2320-269-34-1
FORWARD-REAR AXLE DIFFERENTIAL
This task covers:
a. Removal (page 2-848)
d. Inspection/Replacement (page 2-857)
b. Disassembly (page 2-850)
e. Assembly (page 2-858)
c. Cleaning (page 2-856)
f. Installation (page 2-872)
INITIAL SETUP
Tools
Tools - Continued
Bar, pry, 24-inch
Stand, overhaul
Block, wood (three required)
Tester, spring scale
Caliper, micrometer, OD
Vise, machinist's
Caps, vise jaw
Wire or strong cord, 36-inch
Driftpin, brass, 3/4-inch
Wrench, adjustable
Face, inserted, hammer, medium-plastic
Wrench, impact, air-driven, 3/4-inch drive
Fixture, riveting
Wrench, open-end, 3/4-inch
Gage, thickness, ribbon
Wrench, torque, 1/2-inch drive, 0 to 200 ft-lb
Grinder, pencil, portable
capacity
Hammer, ball-peen, machinist's, 3-lb
Wrench, torque, 3/4-inch drive, 0 to 800 ft-lb
Handle, ratchet, 318-inch drive
capacity
Handle, ratchet, 1/2-inch drive
Wrench, torque multiplier, 3/4-inch drive,
Handle, ratchet, 3/4-inch drive
0 to 800 ft-lb capacity
Hoist, with lifting cables, 4000-lb
capacity
Materials/Parts
Holder, inserted hammer-face
Cloth, emery (item 8, appendix B)
Indicator, dial
Gasket, bearing retainer
Jack, dolly-type
Gasket, differential carrier
Jack, hydraulic hand
(four required)
Pinion setting gage set
Lockwasher, carrier to housing (12 required)
Pliers, slip-joint, angle-nose
Lockwasher, oil scoop to flanged case
Pliers, snapring
Lubricant, rear-axle (item 28, appendix B)
Press, arbor, hand-operated
Paint, oiled red lead (item 37, appendix B)
Press, hydraulic, 75-ton
Pin, cotter, bearing locks (two required)
Puller, gear and bearing
Plates, lock, bearing caps (two required
Punch, drive-pin, blunt-point,
Rags, wiping (item 42, appendix B)
3/8-inch
Rivets (12 required)
Screws, puller, 1/2-inch NC, 3-inch
Sealant, gasket (item 44, appendix B)
(two required)
Seal, oil
Scribe, machinist's
Shims, pinion cage and carrier
Socket, 3/8-inch drive, 7/16-inch
Solvent, drycleaning (item 49, appendix B)
Socket, 1/2-inch drive, 9/16-inch
Spacer, pinion assembly
Socket, 1/2-inch drive, 13/16-inch
Tag, marking (item 50, appendix B)
Socket, 1/2-inch drive, 3/4-inch
Washers, thrust, side (two required)
Socket, 3/4-inch drive, 15/16-inch
Washers, thrust, pinion (four required)
Socket, 314-inch drive, 1 5/8-inch
Socket, deep well, 3/4-inch drive,
1 13/16-inch
Socket, deep well, impact, 3/4-inch
drive, 1 13/16-inch
2-847
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals