 |
|||
|
|
|||
|
Page Title:
SHIPMENT (MAXIMUM DENSITY (LOGISTICAL)( CONFIGURATION) |
|
||
| ||||||||||
|
|
 TM 55-1520-238-S
2-32.7 Remove Left and Right Anti collision
2-32.5 Remove Tailboom Aft Closeout Fairing
Lights. (TM 1 1520 238 23).
and Horizontal Stabilator. (fig. 2-6 and
TM 1 1520 238 23).
a. Stow Anti collision lights. Wrap
a. Secure Stabilator Shims. Secure
with cushioning material (D-5) and se
c
shims in place until installed. Do not re
m
ure with tape (D-13). Secure lights in
ove shims from spacers.
pilots station.
b. Install Stabilator Actuator Sup
p
2-32.8 Install Fly Away Covers.
ort. Mount yoke of support (item 3,
(TM 1 1520 238 23).
table 2-1) to airframe stabilator pivots,
2-32.9 Weigh Helicopter. Weigh each helicopter
and connect actuator rod end to support
and compute the center of gravity. Reduce or redis
t
end fitting. Use removed stabilator pivot
ribute weight as necessary to keep from exceeding
and actuator rod end hardware.
the following limits (maximum tire pressure 125 psi):
c. Static Wicks. To prevent damage to
m
static wicks, loosen one screw and re
a. Main Gear. 5920 lbs per tire.
ove the other in each wick. Rotate the
b. Tail Wheel. 1660 lbs.
wick 100 and tighten screw. Reinstall
first screw in stabilator.
d. Access Covers. Reinstall stabilator
SHIPMENT (MAXIMUM DENSITY (LOGISTICAL)
access covers.
CONFIGURATION).
e. Component Wrap. Wrap stabilator
m
2-33.1 Prepare Helicopter for Tactical Ship
with barrier material (D-1), cushioning
q ent in C 17. Ensure that helicopter is in the re
material (D-5) and secure with tape
guired preloading condition in accordance with para
(D-13).
raph 2-31 thru 2-31.12. Prepare helicopter in
f. Stow Tailboom Aft Closeout Fairing.
accordance with paragraphs 2-33.2 thru 2-33.8.
Wrap fairings with cushioning material
(D-5), secured with tape (D-13) and stow
2-33.2 Remove Hellfire Launchers.
in catwalk area.
a. Removal. Remove Hellfire launchers
2-32.6 Remove ADF Wire Antenna and UHF L
B
(TM 9 1427 475 20).
and, Communications, and Transponder
b. Preservation. Thoroughly coat un
p
Blade Antennas, and FM AM whip antenna
s ainted mounting surfaces with corro
(MWO 1 1520 238 50 37 installed). (fig. 2 8).
ion preventive compound (D-4). Cap or
a. Remove FM AM Whip Antenna. Re
e
wrap all electrical connectors with barri
move fairing. Remove lockwire and loos
e
r material (D-1) sealed with tape
pn antenna lower jam nut. Separate up
(D-13).
er antenna half from lower half.
c. Component Wrap. Wrap each
b. Remove ADF Wire Antenna. Un
c
launcher with barrier material (D-1), se
n
hook end of antenna from standoff termi
ure with tape (D-13).
al spring. Coil antenna and secure to
d. Packaging. Pack each removed and
latch on aft storage bay (R330) with
wrapped launcher in its shipping con
t
twine (D-14).
ainer (item 20, table 2-1).
c. Remove Blade Antennas. Remove
six screws from each antenna flange and
2-33.3 Remove 2.75 Inch Rocket Launchers.
pull on antennas. If sealant will not per
m
a. Removal. Remove rocket launchers
it removal, gently pry antennas with
(TM 9 1055 460 13&P).
plastic (phenolic) tool to break sealant
b. Preservation. Thoroughly coat un
p
loose. Disconnect plugs from receptacles
s ainted mounting surfaces with corro
and remove antennas.
ion preventive compound (D-4). Cap or
d. Remove Lower IFF Antenna.
e
wrap all electrical connectors with barri
emove four screws from antenna base.
r material (D-1) sealed with tape
Remove antenna and detach connector.
(D-13).
e. Stow Blade Antennas. Wrap all an
t
c. Component Wrap. Wrap each
ennas with cushioning material (D-5),
launcher with barrier material (D-1)
n
secured with tape (D-13). Secure anten
as in pilots station.
sealed with tape (D-13).
2-32.6.1 Remove HF Communication Antenna
d. Packaging. Pack each removed and
(MWO 1 1520 238 50 60 installed) Paragraph
wrapped rocket launcher in its shipping
2 11.14.1.
container (item 36, table 2-1).
Change 8
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals