15-Day Organizational Maintenance Allowance

in the applicable allowance column. Items au-

g. 15-Day Organizational Maintenance Allow-

thorized for use as required but not for initial

ance.

stockage are identified with an asterisk in the

(1) The allowance columns are divided into

Allowance Column.

four subcolumns. Indicated in each subcolumn

opposite the first appearance of each item is the

(2) The quantitive allowances for DS/GS

total quantity of items authorized for the num-

levels of maintenance will represent initial stock-

ber of equipments supported. Subsequent appear-

age for a 30-day period for the number of equip-

ances of the same item will have the letters

ment supported.

"REF" in the allowance columns. Items author-

(3) Determination of the total quantity of

ized for use as required but not for initial stock-

parts required for maintenance of more than 100

a g e are identified with an asterisk in the

of these equipments can be accomplished by con-

allowance column.

verting the equipment quantity to a decimal

(2) The quantitative allowances for organi-

factor by placing a decimal point before the next

zational level of maintenance represents one

to last digit of the number to indicate hundred-

initial prescribed load for a 15-day period for

ths, and multiplying the decimal factor by the

the number of equipments supported. Units and

parts quantity authorized in the 51100 allow-

organizations authorized additional prescribed

ance column. Example, authorized allowance for

loads will multiply the number of prescribed

51100 equipments is 40; for 150 equipments

loads authorized by the quantity of repair parts

multiply 40 by 1.50 or 60 parts required.

reflected in the density column applicable to the

i. 1-Year Allowance Per 100 Equipments/

number of items supported to obtain the total

Contingency Planning Purposes. This column

quantity of repair parts authorized.

indicates opposite the first appearance of each

(3) Organizational units providing mainte-

item the total quantity required for distribution

nance for more than 100 of these equipments shall

and contingency planning purposes. The range of

determine the total quantity of parts required

items indicates total quantities of all authorized

by converting the equipment quantity to a de-

items required to provide for adequate support of

cimal factor by placing a decimal point before

100 equipments for one year.

the next to last digit of the number to indicate

hundredths, and multiplying the decimal factor

j. Depot Maintenance Allowance Per 100

by the parts quantity authorized in the 51100

Equipments. This column indicates opposite the

allowance column. Example, authorized allow-

first appearance of each item, the total quantity

ance for 51100 equipment is 40; for 150 equip-

authorized for depot maintenance of 100 equip-

ments multiply 40 X 1.50 or 60 parts required.

ments. Subsequent appearances of the same item

(4) Subsequent changes to allowances will

will have the letters "REF" in the allowance

be limited as follows. No change in the range of

column. Items authorized for use as required but

items is authorized. If additional items are con-

not for initial stockage are identified with an

sidered necessary recommendations should be

asterisk in the allowance column.

forwarded to Commanding Officer, Frankford

k. Illustration Column. This column is divided

Arsenal, ATTN: AMSWESMFW3100 Phila-

as follows:

delphia, Pennsylvania 19137, for exception or

revision to the allowance list. Revisions to the

(1) Figure number column, Indicates the

range of items authorized will be made by the

figure number of the illustration on which the

Commanding Officer, Frankford Arsenal, ATTN:

item is shown.

AMSWE-SMF-W3100, Philadelphia, Pennsyl-

(2) Item number column. Indicates the call

vania 1 9 1 3 7 , based upon engineering ex-

out number used to reference the item in the

perience, demand data, or TAERS information.

illustration.

h. 30-Day DS/GS Maintenance Allowan.ces.

C-4. Special Information

Note. Allowances in GS Column are for GS maintenance

only.

Action change codes indicated in the left hand

(1) The allowance columns are divided into

margin of the listing page denote the following:

three subcolumns. Indicated in each subcolumn,

N--Indicates an added item not included in

opposite the first appearance of each item, is the

previous publications.

total quantity of items authorized for the number

C--Indicates a change in data.

of equipments supported. Subsequent appearances

of the same item will have the letters "REF"

F--Indicates a change in FSN only.

C-3