Table 4-3. Location of Markings - Continued

TM 9-1375-213-34&P

M4- WHEN HINGE AND HASP FITTINGS ARE USED, THE MARKING SHALL APPEAR ON

THE SIDE TO WHICH THE HASP IS FASTENED.

M5- WHEN FLAT BAND STRAPPING IS USED, LOCATE MARKING WITH CLEAR SPACE 1

INCH WIDE AT STRAPPING LOCATION.

M6- THE WORDS "FLASHLESS" OR "SMOKELESS" WHEN REQUIRED IN THE DESCRIP-

TIVE NOMENCLATURE OF THE ITEM PACKED WILL BE SPELLED OUT

COMPLETELY. THE WORDS "FLASHLESS-SMOKELESS" MAY BE ABBREVIATED

WHEN NECESSARY, AS FOLLOWS - "FLHLS - SMKLS".

M7- MARKING SHALL NOT BE EMBOSSED OR INDENTED BELOW THE SURFACE OF

THE WOOD.

MS- INSERT PROPER SHIPPING NAME AND IDENTIFICATION NUMBER AS REQUIRED

BY PACKING AND MARKING BOX DRAWING. PROPER SHIPPING NAME AND

IDENTIFICATION NUMBER ARE TO BE SEPARATED WITH A SPACE.

A- MAY BE PLACED GIRTHWISE ON COVER.

B- ALTERNATIVE: FOR SMALL BOX WITH `TOP HANDLES: MAY BE PLACED ON

SIDE OF BOX, SPACED 1/4 INCH MINIMUM FROM TOP EDGE WITH OTHER

MARKING PRESCRIBED FOR SIDE OF BOX PLACED BELOW PROPER SHIPPING

NAME/IDENTIFICATION NUMBER MARKING SPACED AS SHOWN.

M9- APPLY THE STORAGE TEMPERATURE LIMIT INDICATED, WHEN PACKING ROCKET

AMMUNITION (INCLUDING ROCKETS, ROCKET MOTORS AND JATO UNITS)

CONTAINING NITROCELLULOSE PROPELLANT. STORAGE TEMPERATURE LIMITS

SHALL BE ENCLOSED IN A SQUARE WITH THE WORDS "STORAGE TEMPERATURE

LIMITS". THE TEMPERATURE SHALL BE INDICATED BY A FIGURE FOLLOWED BY

THE LETTER "C" (CELSIUS) OR "F" (FAHRENHEIT) AS APPROPRIATE.

M10- WHEN ROCKET AMMUNITION (INCLUDING ROCKETS, ROCKET MOTORS AND JATO

UNITS) IS PACKED, END OR SIDE EDGE OF BOX TOP OVER NOSE OF ROCKET

AMMUNITION MUST BE MARKED "NOSE END" WHEN WP SMOKE ARTILLERY

AMMUNITION IS PACKED. COVER OF END OF BOX TOWARD WHICH FUZE IS

POINTED MUST BE MARKED "NOSE END". MARKING MAY BE PLACED AT EITHER

END OF BOX TO COINCIDE WITH AMMUNITION POSITION.

M11- INSERT GROSS WEIGHT BY WEIGHING TWO REPRESENTATIVE SAMPLES AND

AVERAGING THE WEIGHT.

M12- MARKING OF BOX SHALL BE AS SPECIFIED IN MIL-STD-129-1 WHEN CARTRIDGES

OF MORE THAN ONE LOT NUMBER ARE PACKED.

M13-

M14- INSERT LOT NUMBER. UNDERLINE ON SIDE OF BOX ONLY, WITH SOLID LINE

1/8 INCH WIDE MINIMUM.

M15- INSERT ZONE MARKING, IF APPLICABLE. THE ZONE MARKING WILL BE MARKED

ON THE BOX WHEN INDICATED ON THE PROJECTILE PACKED. SOLID SQUARES

OF THE SAME COLOR AS THE OTHER LETTERING ON THE BOX SHALL BE USED

TO INDICATE THE WEIGHT ZONE OF ALL AMMUNITION.

M16- INSERT BURSTING CHARGE, IF APPLICABLE. THE BURSTING CHARGE WILL BE

MARKED ON THE BOXES OF ALL HIGH EXPLOSIVE AMMUNITION.

M17- INSERT APPROPRIATE QUANTITY, DESCRIPTIVE NOMENCLATURE, CALIBER AND

WEAPON DESIGNATION AS SHOWN ON APPLICABLE PACKING AND MARKING BOX

DRAWING.

Ml&INSERT NATIONAL STOCK NUMBER AND D.O.D. IDENTIFICATION CODE (DODIC) TO

BE LOCATED AS FOLLOWS:

A- IN LINE WITH THE HASP ON SHALLOW DEPTH BOXES.

B- WILL READ ON ONE CONTINUOUS LINE BUT MAY BE PLACED BELOW HARD-

WARE ON SMALL BOXES OF INSUFFICIENT LENGTH.

C- TO BE PLACED ON THE TOP LINE OF THE MARKING ON THE SIDE OF THE BOX.

D- THE (DODIC) WILL BE SET APART FROM NSN BY A DASH.

M19- INSERT D.O.D. IDENTIFICATION CODE (DODIC) IF APPLICABLE. (DODIC) STARTS

AT BOTTOM OF CLEAT OR END BATTEN (WIREBOUND BOXES).

4-13