 |
|||
|
|
|||
|
|
|||
| ||||||||||
|
|
 TM 5-6350-262-14/9
NAVELEX 0967-466-9090
TO 31S9-4-32-1
7-12.
Module Installation Install
(9) Install and tighten five screws (3).
a.
replacement module as follows: a. Place
(10) Place cover (2) in position on the
the data receiver, if used, in position (fig.
chassis.
7-1) and tighten the four captive screws making certain
(11) Install and tighten five screws (1).
the connector is properly engaged.
b.
Slide the module into position in the
7-14. Disassembly and Assembly of Status
monitor cabinet rack making certain the connector is
Modules
properly engaged.
a.
Disassembly. The status module can be
c.
Install and tighten the four 6-32 screws.
disassembled as necessary for repair and parts
d.
Close and lock the monitor cabinet door.
replacement by the following procedures. Component
e.
An operational checkout of a replacement
locations and attaching parts are illustrated in figure C-2.
monitor module may be performed after installation.
(1) Remove five screws (1, fig. C-2)
Refer to TM 5-6350-262-14/4 for detailed procedures.
and remove cover (2).
(2) Remove five screws (3) and
7-13. Disassembly and Assembly of Alarm
carefully pivot cover (4) out of chassis.
Modules
(3) Being careful not to bend PWB
a.
Disassembly. The alarm module can be
connector pins, remove interconnect wiring board (5)
disassembled as necessary for repair and parts
and the PWB at each end of PWB A1 (9) and PWB A2
replacement by the following procedures. Component
(7).
locations and attaching parts are illustrated in figure C-1.
(4) Remove cover (4) with PWB (9)
(1) Remove five screws (1, fig. C-1)
and (7) still attached.
and remove cover (2).
(5) Remove five screws (6) and
(2) Remove five screws (3) and
remove PWB A2 (7).
carefully pivot cover (4) out of chassis.
(6) Unsolder two coil leads from coil
(3) Being careful not to bend PWB
(13) PWB A1 (9), terminals E22 and E23 (see fig. 64).
connector pins, remove the interconnect wiring boards
(7) Remove five screws (8, fig. C-2)
from each end of I WB A1 (6).
and remove PWB A1 (9).
(4) Remove cover (4) and PWBA1 (6).
(8) Remove two nuts (10), washers
(5) Unsolder two coil leads from coil
(11), and screws (12) and remove coil (13).
(10) on PWB Al, terminals E22 and E23. See figure 6-
(9) Any connectors, lamps, or switches
can be removed by disconnecting the electrical
(6) Remove five screws (5, fig. C-1)
connections (see fig. 6-4) and removing the component
and remove PWBA1 (6).
(see fig. C2).
(7) Remove two nuts (7), washers (8),
b.
Assembly. The status module can be
and screws (9) and remove coil (10).
assembled by the following procedures. Component
(8) Any connectors, lamps, or switches
locations and attaching parts are illustrated in figure C-2.
can be removed by disconnecting the electrical
(1) Place coil (13, fig. C-2) in position
connections (fig. 63) and removing the component (fig.
on cover (4).
(2) Install two screws (12), washers
b.
Assembly. The alarm module can be
(11), and nuts (10) and tighten.
assembled by the following procedures. Component
(3) Place PWBA1 (9) in position on
locations and attaching parts are illustrated in figure C-1.
cover (4).
(1) Place coil (10) in position on cover (4).
(4) Install five screws (8) and tighten.
(2) Install two screws (9), washers (8), and
(5) Connect coil (13) leads to PWBA1
nuts (7) and tighten.
(9) terminals E22 and E23 as shown on schematic (fig.
(3) Place PWB A1 (6) in position on cover
6-4).
(4).
(6) Place PWB A2 (7) in position on
(4) Install five screws (5) and tighten.
PWBA1 (9) and install and tighten five screws (6).
(5) Connect coil leads to PWB A1
(7) Place cover (4) in position near the
terminals E22 and E23 as shown on schematic (fig. 6-
chassis.
(8) Being careful not to bend PWB
(6) Place cover (4) in position near the
connector pins, install interconnect wiring board (5) and
chassis.
the PWB at each end of PWB A1 (9) and PWB A2 (7).
(7) Being careful not to bend PWB
(9) Place the cover (4) in position on
connector pins, install interconnect wiring boards to
the chassis.
each end of PWB A1 (6).
(10) Install and tighten five screws (3).
(8) Place the cover (4) in position on
(11) Place cover (2) in position on the
the chassis.
chassis.
(12) Install and tighten five screws (1).
7-7
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals