APPENDIX C BASIC ISSUE ITEMS LIST, ITEMS TROOP INSTALLED OR AUTHORIZED LIST REPAIR PARTS AND SPECIAL TOOLS LIST

TM 5-6350-262-14/4

APPENDIX C

BASIC ISSUE ITEMS LIST, ITEMS TROOP

INSTALLED OR AUTHORIZED LIST REPAIR

PARTS AND SPECIAL TOOLS LIST

Section I. INTRODUCTION

C-1. Scope

PC ..................tem procured and stocked and which

This appendix lists basic issue items; items troop

.......................otherwise would be coded PA except

installed or authorized; repair parts; special tools; test,

.......................that it is deteriorative in

nature.

measurement, and diagnostic equipment (TMDE); and

PD .................. upport item, excluding support

other support equipment required for operation and

.......................equipment, procured for initial issue or

performance of organizational, direct support and

.......................outfitting and stocked

only for

general support maintenance of the Magnetic Weapon

.......................subsequent or additionalni tial issues or

Sensor.

.......................outfitting. Not subject to automatic

C-2. General

.......................replenishment

The Basic Issue Items List, Items Troop Installed or

PE ................... upport equipment procured and

Authorized List and Repair Parts and Special Tools List

.......................stocked for initial issue or outfitting to

are divided into the following sections:

.......................specified maintenance repair

Section 11. Basic Issue Items List. (Not

.......................activities

Applicable}

PF ................... upport equipment which will not be

Section III. Items Troop Instated or Authorized

.......................stocked but which will be centrally

List. (Not Applicable

.......................procured on demand.

Section IV. Repair Parts List. A list of repair parts

PG ..................tem procured and stocked to provide

authorized for use in the performance of maintenance.

for ................... ustained support for the life of the

The list also includes parts which must be removed for

.......................equipment. It is applied to an

replacement of the authorized parts. Parts list are

.......................i.tem peculiar to the equipment which,

composed of assembly groups in ascending numerical

.......................because of probable discontinuance or

sequence, with the parts in each group listed in figure

.......................shutdown of production falities, would

and item number sequence. Bulk materials are listed in

.......................prove uneconomical to reproduce at a

FSN sequence.

.......................l.ater time.

d Section V. Special Tools List. (Not applicable

KD ................... n item of a depot overhaul/repair kit

Section VI. Federal Stock Number and Part

.......................and not purchased separately. Depot kit

Number Index. A list in ascending numerical sequence

.......................defined as a kit that provides

of all Federal stock numbers appearing in the listings

.......................i.tems required at the time of overhaul or

followed by a list, in alpha-numeric sequence, of all part

.......................repair.

numbers appearing in the

KF ................... n item of a maintenance kit and not

listings.

Federal stock numbers and part numbers

.......................purchased separately. Maintenance kit

are cross-referenced to each illustration figure and item

.......................defined as a kit that provides an item

number appearance.

.......................that can be replaced at organizational or

C-3. Explanation of Columns

.......................i.ntermediate levels of maintenance.

The following provides an explanation of columns found

KB...................Item included in both a depot

in the tabular listings:

.......................overhaul/repair kit and a maintenance

Illustration This column is divided as

.......................kit.

follows:

MO ..................tem to be manufactured or fabricated at

(1) Figure number.

Indicates the figure number of

.......................organizational level.

the illustration in which the item is shown.

MF ..................tem to be manufactured or fabricated at

(2) Item number. The number used to identify each

.......................the direct support maintenance level

item called out in the illustration.

MH ..................tem to be manufactured or fabricated at

Source, Maintenance and Recoverability

.......................the general support maintenance level.

Codes

MD ..................tem to be manufactured or fabricated at

(SMR).

.......................the depot maintenance level.

(1) Source code. Source codes are assigned to support

AO ..................tem to be assembled at organizational

items to indicate the manner of acquiring support items

.......................l.evel

for maintenance, repair, or overhaul of end items.

AF ...................tem to be assembled at direct support

Source codes are entered in the first and second

.......................maintenance level.

positions of the Uniform SMR Code format as follows:

AH ..................tem to be assembled at general support

Code

Definition

.......................maintenance level.

PA ................... Item procured and stocked for

AD ..................tem to be assemble at depot

........................ anticipated or known usage.

.......................maintenance level

PB ................... Item procured and stocked for insurance

XA ...................tem is not procured or stocked because

........................ purposes because essentiality dictates

.......................the requirements for .the item will result

........................ that a minimum quantity be available in

.......................i.n the replacement of the newt higher

........................ the supply systems.

.......................assembly.

C-1