Quantcast Table 4-3. Location of Markings

 

Click here to make tpub.com your Home Page

Page Title: Table 4-3. Location of Markings
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Figure 4-1. Woodbox - location of markings.
Up
TM-9-1375-213-34-P Demolition Materials Manual
Next
Table 4-3. Location of Markings - Continued - TM-9-1375-213-34-P0025
TM 9-1375-213-34&P
Table 4-3. Location of Markings
PACKAGING COMPONENTS
SEAL, METALLIC-8794342-1, -2, -3, -4, -5, OR 6
PACKING FOR LIGHT BOXES 9325874
NOTES:
1-SPEC MIL-A-002550 APPLIES
2-MATERIAL: INK, STENCIL, BLACK NO. 37038, TYPE II, III, OR IV SPEC A-A-208.
A-ALTERNATIVE: INK IN ACCORDANCE WITH DWG 9211789
B-ALTERNATIVE: LACQUER (ENAMEL) NITROCELLULOSE AND ACRYLIC, AEROSOL
SPEC TT-L-50
C-ALTERNATIVE: PAINT, STENCIL, FLAT, SPEC A-A-1558
D-ALTERNATIVE: MARK IN ACCORDANCE WITH DWG 9295098 WIDTH OF LETTER
STROKE SHALL BE APPROXIMATELY EQUAL TO THAT OBTAINED WITH STENCIL.
3-MATERIAL: PAINT, ORANGE NO. 32246, SPEC TT-P-96
A-ALTERNATIVE: PAINT, STENCIL, FLAT, SPEC A-A-1558
B-ALTERNATIVE: LACQUER (ENAMEL) NITROCELLULOSE AND ACRYLIC. AEROSOL.
ORANGE NO. 12197 OR NO. 12215, SPEC TT-L-50
MARKING INSTRUCTIONS
M l THE MARKING OF WOOD SHIPPING BOXES FOR AMMUNITION ITEMS SHALL BE
PLACED ON TOP ONE SIDE AND BOTH ENDS. (BOTH ENDS TO BE MARKED
ALIKE) IN ACCORDANCE WITH TYPICAL MARKING DIAGRAMS, NOTES AND
MARKING INSTRUCTIONS CONTAINED ON THIS DRAWING AND APPLICABLE
PACKING AND MARKING BOX DRAWING.
M2- LETTERS AND FIGURES SHALL BE MARKED WITH BLACK STENCIL INK.
(NOTE 2)
M3- THE DESIRED HEIGHT OF LETTERS AND FIGURES AND MINIMUM SIZE ALLOWED
ARE AS FOLLOWS:
DESIRED SIZE
MINIMUM SIZE
MARKING
A- NATIONAL STOCK NUMBER AND D.O.D.
IDENTIFICATION CODE (DODIC) ------------ 1.INCH HIGH
7/16 INCH HIGH
B- LOT NUMBER ------------------------------------------ 1.INCH HIGH
1. INCH HIGH
THE LETTERS AND FIGURES OF THE
LOT NUMBER MAY BE 7/16 INCH MIN
HEIGHT ON CLEATS OF SHALLOW
DEPTH BOXES AND ON SIDE OF BOXES
ONLY IN CASES WHERE ALLOWABLE
SPACE IS INSUFFICIENT FOR 1 INCH
CHARACTERS.
C- DESCRIPTIVE NOMENCLATURE,
7/16 INCH HIGH
CALIBER AND WEAPON DESIGNATION ---- 1.INCH HIGH
D- ALL OTHER MARKING --------------------------------------------------------------------- 7/16 INCH HIGH
E- THE SIZES AND SPACES OF LETTER BLOCKS ARE REPRESENTATIVE OF
STANDARD MACHINE CUT STENCIL LETTERING
F- DEVIATIONS IN SIZE OF LETTERS AND FIGURES WITHIN LIMITS SPECIFIED
ABOVE WILL BE PERMITTED WHEN SIZE OF BOX IS SUCH THAT THE DESIRED
SIZE SPECIFIED IS NOT PRACTICAL.
G- WHEN NECESSARY TO DEVIATE FROM DESIRED SIZE, THE LETTERS AND
FIGURES SHALL BE APPROXIMATELY PROPORTIONAL TO THE SIZES LISTED.
H- THE RELATIVE POSITIONS OF THE VARIOUS MARKING SHALL BE AS SHOWN.
MARKING SHALL BE PLACED TO AVOID INTERFERENCE WITH WIRES OR
HARDWARE.
I- THE MARKING BLOCKS
SHOWN ARE FOR ILLUSTRATION PURPOSES
ONLY AND DO NOT NECESSARILY REPRESENT THE REQUIRED INFORMATION
TO BE ENTERED.
4-12

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc.