Quantcast Section VII. MAINTENANCE OF LINKAGE ASSEMBLY

 

Click here to make tpub.com your Home Page

Page Title: Section VII. MAINTENANCE OF LINKAGE ASSEMBLY
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Replacement of Lamp Assembly cont'd
Up
TM-9-1270-212-14-P Fire Control Subsystem Helmet Directed XM128 P/N 2277716-00 NSN 1270-00-122-9449 Manual
Next
AH-1S Helicopter
TM 9-1270-212-14&P
Section VII. MAINTENANCE OF LINKAGE ASSEMBLY
3-13. General.
soaked in alcohol or other solvent conforming to
MIL-A-6091.
Organizational level maintenance of the linkage
b. If small nicks or light damage is detected, rubbing
assemblies is limited to cleaning of the rails.
with a crocus cloth meeting Federal Specification P-C-458c
3-14. Rail Assembly Cleaning.
should satisfactorily return the rails to good condition.
Wipe the rails clean before ruining the carriage along them.
a. Wipe any paint or insecticide spray, window cleaner,
oil, or other residue from the rails with a lint-free cloth
Section VIII. MAINTENANCE OF ELECTRONIC INTERFACE ASSEMBLY
3-15. General.
(3) Remove the screw and washer that secure the
EIA to each of the four isolator mounts and remove the
Organizational level maintenance of the electronic
EIA. Retain the four screws and washers.
interface assembly (EIA) consists of removal, installation,
(4) Remove each of the four isolator mounts by
and electrical adjustment procedures.
removing the two screws and washers. Retain these eight
screws and washers.
(5) Using the hardware retained in (3), install the
a. AH-1S(Mod) Helicopter.
isolator mounts on the EIA.
(l) Loosen the captive screws and disconnect cable
3-17. Installation (fig. 3-2).
connectors A2P1, W1P2, and 17A1P1 from the EIA.
(2) Remove the screw and washer that secure the
a. AH-1S(Mod) Helicopter.
bonding jumper to the isolator mount. Retain the screw
and washer.
(1) Inspect the EIA for dents, scratches, missing
hardware, and bent connector pins.
(3) Remove the four mounting screws that secure the
EIA to the isolator mounts and remove the two cable
(2) Remove the four screws and washers that secure
clamps secured by two of the mounting screws.
the isolator mounts to the EIA.
(4) Remove the other seven screws and washers that
(3) Install the isolator mounts to the airframe, using
secure the isolator mounts to the airframe. Retain the
the seven screws and washers retained in paragraph
screws and washers.
3-16a(4).
(5) Secure the isolator mounts to the EIA, using the
(4) Install the EIA on the isolator mounts, using the
hardware removed in (3) above except for the cable clamps.
four screws and washers removed in (2) and securing the
two cable clamps with two of the screws.
b. AH-1S Helicopter.
(5) Using the screw and washer retained in paragraph
3-16a(2), secure the bonding jumper to the isolator mount,
(1) Remove the nut, screw, and washer that secure
with the bonding-jumper lug between the washer and the
the bonding jumper to the helicopter airframe. Replace the
nut. screw, and washer in the airframe hole.
screwhead.
(6) Connect cable connectors A2P1, W1P2, and
(2) Loosen the captive screws and disconnect cable
17A1P1 to the EIA and tighten the captive screws.
connectors A2P1, W1P2, and 17A1P1 from the EIA.

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc.