Quantcast APPENDIX B MAINTENANCE ALLOCATION CHART - TM-5-6350-264-14-P-80035

 

Click here to make tpub.com your Home Page

Page Title: APPENDIX B MAINTENANCE ALLOCATION CHART
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
REFERENCES cont'd - TM-5-6350-264-14-P-80034
Up
TM-5-6350-264-14-P-8 Switch Alarm Latching SA-1954( )/FSS-9(V) NSN
Next
COLUMN ENTRIES - TM-5-6350-264-14-P-80036
TM 5-6350-264-14&P-8
NAVELEX EE181-AA-OMI-090/E121 SA-1954
T.O. 31S9-2FSS9-1-8
APPENDIX B
MAINTENANCE ALLOCATION CHART
Section I. INTRODUCTION
B-1. GENERAL.
d. Adjust. To maintain, within prescribed limits, by
bringing into proper or exact position, or by setting the
a. This section provides a general explanation of
operating characteristics to specified parameters.
all maintenance and repair functions authorized at
various maintenance levels.
e. Align. To adjust specified variable elements of
an item to bring about optimum or desired performance.
b. Section II designates overall responsibility for the
performance of maintenance functions on the identified
f. Calibrate. To determine and cause corrections to
end item or component.  The implementation of the
be made, or to be adjusted on instruments for test,
maintenance functions upon the end item or component
mearing and diagnostic equipment used in precision
will be consistent with the assigned maintenance
measurement.
Consists  of  comparisons  of  two
functions.
instruments, one of which is a certified standard of
known accuracy, to detect and adjust any discrepancy in
c.
Section III lists the special tools and test
the accuracy of the instrument being compared.
equipment required for each maintenance function as
referenced from section II.
g. Install. The act of emplacing, seating, or fixing
into position an item, part, or module in a manner to
d. Section IV contains supplemental instructions or
allow the proper functioning of an equipment or system.
explanatory notes for a particular maintenance function.
(Not Applicable)
h. Replace. The act of substituting a serviceable
like part, subassembly, or module for an unserviceable
counterpart.
B-2.
MAINTENANCE FUNCTIONS.
Maintenance
functions are defined as follows:
i.  Repair.
The  application of maintenance
services (inspect, test, service, adjust, align, calibrate, or
replace)  or  other  maintenance  actions  (welding,
a. Inspect. To determine the serviceability of an
grinding, riveting, straightening, facing, re-machining, or
resurfacing) to restore serviceability to an item by
item by comparing its physical, mechanical and/or
correcting specific damage, fault, malfunction, or failure
electrical characteristics with established standards
in a part, subassembly, module, end item or system.
through examination.
j.  Overhaul.  That maintenance effort (service/
b.  Test.  To  verify serviceability and detect
incipient failure by measuring the mechanical or
actions) necessary to restore an item to a completely
electrical characteristics of an item and comparing those
serviceable/operational  condition  as  prescribed  by
characteristics with prescribed standards.
maintenance standards (i.e., DMWR) in appropriate
technical publications. Overhaul is normally the highest
c.  Service.  Operations  required periodically to
degree of maintenance
keep an item in proper operating condition, i.e., to clean,
to preserve, to drain, to paint, or to replenish fuel,
lubricants, hydraulic fluids, or compressed air supplies.
B-1

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business