Quantcast CHAPTER 5 DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE INSTRUCTIONS - TM-5-6350-264-14-P-40016

 

Click here to make tpub.com your Home Page

Page Title: CHAPTER 5 DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE INSTRUCTIONS
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
CHAPTER 4 ORGANIZATIONAL MAINTENANCE INSTRUCTIONS - TM-5-6350-264-14-P-40015
Up
TM-5-6350-264-14-P-4 Detector Vibration Signal DT-546/FSS-9(V) NSN
Next
Table 5-1. Troubleshooting Procedures - TM-5-6350-264-14-P-40017
TM 5-6350-264-14&P-4
NAVELEX EE 181-AA-OMI-050/E121 DT546 M9442
TO 31S9-2FSS9-1-4
CHAPTER 5
DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE INSTRUCTIONS
Section I. REPAIR PARTS, SPECIAL TOOLS AND EQUIPMENT
5-1. SPECIAL TOOLS. No special tools are required
illustrated in the repair parts and special tools list
covering direct and general support maintenance for this
for the Vibration Sensor.
equipment in appendix C of this manual.
5-2.
REPAIR PARTS.
Repair parts are listed and
Section II. TROUBLESHOOTING
5-3. TROUBLESHOOTING PROCEDURES.
a.
This section contains troubleshooting information
for locating and correcting most of the operating
troubles which may develop in the Vibration
Sensor.
Each malfunction for an individual
component, unit, or system is followed by a list of
tests or inspections which will help you to
determine corrective actions to take. You should
The Audible Alarm presents a noise hazard to personnel
perform the test/ inspections in the corrective
in the area.  The noise level exceeds the allowable
actions column in the order listed.
limits for unprotected personnel. Authorized protective
equipment must be worn by all personnel in the work
b.
This manual cannot list all malfunctions that may
area.
occur, nor all tests or inspections and corrective
actions.  If a malfunction is not listed or is not
NOTE
corrected by listed corrective actions, notify your
supervisor.
If the Audible Alarm is installed, it must be disabled
BEFORE
any
troubleshooting
procedures
are
c.
The table lists the common malfunctions which you
attempted.  Disable the Alarm by setting the key-
may find during the operation or maintenance of
operated switch on Control Unit to TEST/RESET
the Vibration Sensor or its components.  You
position. Open Audible Alarm, remove faceplate, and
should  perform  the  test/inspections  in  the
turn off power switch. After troubleshooting the Audible
corrective actions column in the order listed.
Alarm must be reactivated.  Activate the Alarm by
setting the key-operated switch on Control Unit to
d.
Check all available information on the equipment
TEST/RESET position.  Turn Alarm power switch on,
for aid in diagnosing problems.
replace faceplate, close and lock Audible Alarm door.
Turn key-operated switch on Control Unit to SECURE or
e.
Make a visual inspection of the equipment.
ACCESS.
NOTE
Before you use table 5-1, be sure you have performed
all
applicable
operating
checks.
5-1

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business