Quantcast COLUMN ENTRIES - TM-5-6350-264-14-P-110087

 

Click here to make tpub.com your Home Page

Page Title: COLUMN ENTRIES
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
APPENDIX B MAINTENANCE ALLOCATION CHART - TM-5-6350-264-14-P-110086
Up
TM-5-6350-264-14-P-11 Cabinet Monitor Type A CY 7359/FSS-9(V) NSN
Next
Section II. MAINTENANCE ALLOCATION CHART - TM-5-6350-264-14-P-110088
TM 5-6350-264-14&P-11
NAVELEX EE 181-AA-OMI-120/E121 C-7359-60-1
T.O. 31S9-2FSS9-1-11
j.
Overhaul.  That maintenance effort (service/actions) necessary to restore an item to a completely
serviceable/operational condition as prescribed by maintenance standards (i.e., DMWR) in appropriate technical
publications. Overhaul is normally the highest degree of maintenance performed by the Army.
Overhaul does not
normally return an item to like new condition.
k.
Rebuild. Consists of those services/actions necessary for the restoration of unserviceable equipment to a like
new condition in accordance with original manufacturing standards.  Rebuild is the highest degree of materiel
maintenance applied to Army equipment.  The rebuild operation includes the act of returning to zero those age
measurements (hours/miles, etc.) considered in classifying Army equipments/components.
B-3. COLUMN ENTRIES.
a.
Column 1, Group Number. Column 1 lists group numbers, the purpose of which is to identify components,
assemblies, subassemblies, and modules with the next higher assembly.
b.
Column 2, Component/Assembly. Column 2 contains the names of components, assemblies, subassemblies,
and modules for which maintenance is authorized.
c.
Column 3, Maintenance Function. Column 3 lists the functions to be performed on the item listed in column
2.
d.
Column 4, Maintenance Level. Column 4 specifies, by the listing of a "work time" figure in the appropriate
subcolumn(s), the lowest level of maintenance authorized to perform the function listed in column 3.  This figure
represents the active time required to perform the maintenance function at the indicated level of maintenance. If the
number or complexity of the tasks within the listed maintenance function varies at different maintenance levels,
appropriate "work time" figures will be shown for each level. The number of man-hours specified by the "work time"
figure represents the average time required to restore an item (assembly, subassembly, component, module, end item,
or system) to a serviceable condition under typical field operating conditions. This time includes preparation time,
troubleshooting time, and quality assurance/quality control time in addition to the time required to perform the specific
tasks identified for the maintenance functions authorized in the maintenance allocation chart.  The symbol designations
for the various maintenance levels are as follows:
C................................. Operator or crew
O ................................ Organization maintenance
F ................................. Direct support maintenance
H................................. General support maintenance
D................................. Depot maintenance
e.
Column 5, Tools and Equipment. Column 5 specifies, by code, those common tool sets (not individual tools)
and special tools, test, and sup- port equipment required to perform the designated function.
f.
Column 6, Remarks.  Column 6 contains an alphabetic code which leads to the remark in section IV,
Remarks, which is pertinent to the item opposite the particular code.
B-2

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business