Quantcast Table 7-1. Control Unit Performance Standards - Continued - TM-5-6350-262-14-50055

 

Click here to make tpub.com your Home Page

Page Title: Table 7-1. Control Unit Performance Standards - Continued
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Table 7-1. Control Unit Performance Standards
Up
TM-5-6350-262-14-5 Control Unit Alarm Set C-9412( )/FSS-9 (V) (6350-228-2735) Manual
Next
Table 7-1. Control Unit Performance Standards - Continued - TM-5-6350-262-14-50056
TM 5-6350-262-14/5
NAVELEX 0967-466-9050
TO 31S9-4-38-1
Table 7-1. Control Unit Performance Standards - Continued
Control Setting
Step
Test
Performance
No.
Test
Equipment
Procedure
Standard
Equipment
Under Test
Operating mode switch:
j. None.
a. All alarm LED's should
TEST/RESET, then
go out.
SECURE
b. Alarm LED F should illum-
inate after expiration of
exit time delay.
k. Disconnect orange
a. Alarm LED A
jumper wire at
should not illumi-
terminal 1 of ter-
nate.
minal board A.
l. Connect orange
a. None.
jumper wire at
terminal A-1 and
install orange
jumper wire be-
tween terminals 1,
2, and 3 on ter-
minal board F.
m. Connect TS352B
a. Meter should indi-
negative lead to
cate less than 0.5
ground and posi-
volts at each test
tive lead momen-
point.
tarily to each of
the following test
points:
AlTP1, A2TP1
A2TP2, A3TP1,
A3TP2, A4TP1,
A4TP2, A5TP1,
A5TP2, A6TP1,
A6TP2, A7TP1, and
A7TP2.
5
TS352B:
POWER: ON
a. Connect TS352B
a. None.
+D.C.
Operating mode
negative lead to
50V
switch: TEST/
ground. Connect
RESET
positive lead to
test point A10TP1.
Operating mode
b. None.
a. Meter should indi-
switch: SECURE
cate 19 to 21 V dc.
c. Remove one end of
a. Meter indication
jumper wire con-
should drop to ap-
nected between
proximately 0.5
terminals L2-3 and
volt when jumper
-4.
connection is
broken.
d. Reconnect jumper
a. None.
wire.
6
DC power supply:
POWER: OFF
a. Connect TS352B negative
a. None.
VOLTAGE: 20 V dc
Operating mode switch:
lead to ground. Con-
indication on meter.
TEST/RESET
nect positive lead to
CURRENT: 1A
test point A10TP1.
TS352B:
b. Remove fuse F2.
a. None.
+D.C.
POWER: ON
c. Connect dc power supply
a. None.
50V
negative lead to ground
and positive lead to
TB23.
Operating mode switch:
d. None.
a. TS352B meter should
SECURE
indicate 19 to 21
V dc.
7-15

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business